Compare Drill Drivers by voltage from Black & Decker, Bosch, DeWalt, Hitachi, Makita & Ryobi

Click to Compare Prices from Top Retailers!

Drill Drivers To Consider

Perfect examples of 12v Cordless Drill Drivers include the Black & Decker CD12CA 12v Drill Driver, Bosch PSR 12v Drill Driver, DeWalt DC740KA 12v Drill Driver, Hitachi 12DVF3 12v Drill Driver, Makita 6319DWDE3 12v Drill Driver, and the Ryobi CHD1202 12v Drill Driver

In Case 14.4v Cordless Drill Drivers are better suited, then make sure to take a peek at the Black & Decker CP142KB 14.4v Drill Driver, Bosch PSR 14.4v Drill Driver, DeWalt DC728KA 14.4v Drill Driver[/LINK], the Hitachi DSDL Li-Ion 14.4v Drill Driver,Makita BHP442RFE14.4v Drill Driver, or the Ryobi CCD-1441 14.4v Drill Driver

For all your your 18v Cordless Drill Drivers needs, go ahead and review the
Black & Decker CD18CA 18v, Bosch PSR18-2 Li-Ion 18v, DeWalt DC759KB 18v, Hitachi DS18DMR 18v, the Makita 6390DZ 18v or the Ryobi CHP-1802 18v

The number of cordless drill drivers is now huge, and all mains powered drills have their cordless battery equivalents. 9.6 volt to 14.4 volt drill/drivers might be used as a rotary drill or screwdriver. 12 volt to 18 volt cordless drill drivers can also have a hammer action. 12 and 14.4 volt machines are ok on hammer action for brick but would struggle drilling concrete and other hard masonry, if you need the drill to undertake this type of work then you might look at the 18 volt models that are available. Then there are the 18 volt to 36 volt SDS type of drills. These are manufactured for masonry work, and with a chuck adaptor these might be turned into rotary drill drivers. Also with the SDS type of cordless drill you might get some of them with roto stop which then turns them into a demolition hammer drill.

SDS (Special Direct System) Drills come in two standard sizes and they are SDS Plus (10mm) and SDS-Max (18mm). These sizes relate the size of the shank. SDS Plus is the most common and can withstand a hammer of up to 4Kg, and SDS Max for hammers over 5Kg. SDS Plus grips the drill bit in two places whereas SDS Max grip in three places. With the SDS drill you can use a chuck adaptor that when used enables the use of standard drill bits for rotary drilling. It is wise to avoid SDS Drills that do not have a safety clutch. If the drill bit jams and is unable to turn a safety clutch might stop the drill body from spinning. This spinning might cause severe damage to the wrist and arm with the possibility of the drill being yanked from your hand, jumping out of the hole and coming into contact with a part of the body. A safety clutch might be high on your list of required features.

Any tool might feel like an extension of your hand. The tool may feel great while standing in the store aisle but try to imagine what it might feel like after a few hours of use. While in the store make sure all controls are convenient, and check to see if the forward/reverse and high/low speed switches in particular are easy to use.

Cordless drill drivers are measured in volts. Drills are available in everything from around 2 volts (for a cordless screwdriver) to the newest 24-volt tools. Higher voltage means heavier weight so consider buying a tool that might meet 80-90% of your needs. Twelve to 14.4 volt models are the most popular, and they might usually meet most homeowner's work needs. Corded drills are measured in amps. Generally, a higher amperage motor means more power.

Lithium-ion batteries (sometimes abbreviated Li-ion batteries) are a type of rechargeable battery in which a lithium ion moves between the anode and cathode. The lithium ion moves from the anode to the cathode during discharge and from the cathode to the anode when charging.

If a Li-ion battery is stored with too low a charge, there is a risk of allowing the charge to drop below the battery's low-voltage threshold, resulting in an unrecoverable dead battery. Once the charge has dropped to this level, recharging it might be hazardous. Some batteries therefore feature an internal safety circuit which might stop charging in this state, and the battery might be for all practical purposes dead. In circumstances where a second Li-ion battery is available for a given device, it is recommended that the unused battery be discharged to 40% and placed in the refrigerator to prolong its shelf life. While the battery might be used or charged immediately, some Li-ion batteries might provide more energy when brought to room temperature.

An electric or portable (battery powered) drill can be a scary thing. But they aren’t hard to use. The most common drill drivers come in a pistol shape, making them easy to hold and use. The drill has a trigger you squeeze in order to make the drill bit turn. Sometimes there is also a safety button located on the pistol handle that has to be pressed at the same time you squeeze the trigger in order to make the drill bit turn. The battery pack is usually inserted into a docking station on the bottom of the pistol handle. Between uses the battery pack is charged in another docking station which is connected to an electrical outlet.

Not all holes need to go all the way through the material. Some holes need only be a certain depth in the wood. The easiest way to make certain you drill the correct depth is to measure the necessary hole depth on your drill bit. Then mark that point on the bit with a marker or wrap some tape around the bit at the measured spot. Then when you drill only insert the drill bit to the mark or tape. You might also purchase bit collars that slide over the bit and are secured at the appropriate depth. The collars usually attach with a small hex wrench or screwdriver. The drilling is undertaken and you have to get the bit out. Give the drill a little power to spin the bit and slowly pull it out of the hole. Don’t be too speedy or pull it out without spinning the bit. Either of these may cause the bit to bind in the hole. The hole is complete and now you need to attach the fastener. Bits can be inserted into the drill turning the drill into a screwdriver or wrench. If you are attaching screws determine the size of the screw head and select a matching screwdriver bit. Connect the screwdriver bit to the drill in the same way you would other bits. Put the bit head in the screw head and squeeze the trigger. Be careful not to provide so much power that you go all the way through the material (if that’s not called for) or force the screw head too far down into the material. It’s easy to get carried away with the power of the drill. If you are attaching a bolt fastener you might also purchase bolt sockets that might be attached to the drill. Match the bit size with the bolt, attach the bit to the drill, and screw in the bolt.

Screwdriver bits are manufactured to fit in rechargeable cordless drill drivers. These bits have a hexagonal shank and are ideal for drilling pilot holes but are limited by the low power of these type of screwdrivers and the limited size of small bits available. To sharpen use a drill sharpener, a grindstone jig or an oilstone.

DIY Safety tips:

If you need to change a mains fuse, check the correct rating for that circuit - the blown fuse might have been incorrect in the first place. Using a thicker fuse wire than the correct rating is hazardous. Switch off the power and remove the fuse for the relevant circuit before carrying out any work, or inspecting, either it, or the appliances connected to it. Never inspect, or carry out work on, any part of the system with the power on. Make sure that power cannot be inadvertently restored by someone else.
When fixing or checking electrical appliances or connections, always turn off the power and remove the fuse or circuit breaker (MCB). If you're fixing an electrical appliance, turn off the appliance at the plug and pull out the plug. Wear rubber-soled shoes when working on electrics. Cover electrical switches which are broken. Switch off at the mains and remove the fuse to that line, and keep it with you, so even if the power is switched on accidentally the line might stay dead and not you, while you carry out a job. The tapes are a reminder for you and a warning to others. Call in professional help if you do not know what you are doing.

Keep your head: if any of your tools has a loose head or handle, replace the whole tool or have it repaired by a professional. Keep a tool box tidy for easy access and always use the cover guards which come with tools such as saws, knives and chisel blades. Buy equipment and household appliances which are made to a British or European standard or carry an approved product quality and safety mark. There might be a label on the product.

Take extra care with old paint. Some old paint could give off harmful dust and pose a poisoning hazard if ingested by small children. You must not burn off old paint or rub it down with dry sandpaper or a power sander; you might clean up properly, using a high efficiency industrial vacuum cleaner with heavy duty filters. Have a basic First Aid kit accessible.

Wear safety goggles whenever there may be a danger of flying debris - for example when using power tools.

Cordless Drill Drivers

compare 12v 14.4v 18v drill driver

Compare Drill Drivers by voltage from Black & Decker, Bosch, DeWalt, Hitachi, Makita & Ryobi

Click to Compare Prices from Top Retailers!

Drill Drivers To Consider

Cordless Drill Drivers